Unfortunately, respraying your car at an auto body shop can leave a serious dent in your wallet. Luckily, between paying a professional and living with the scratch, there’s a third option: fix the scratch yourself. Use these steps as a guide for your at-home car scratch repair project.
First, Establish Scratch Depth
Not all scratches are created equal! Before you can repair your scratch, you’ll need to establish its depth.
The clear coat is the last and outermost layer of paint on your vehicle – below that is the paint (basecoat,) the primer, then the actual metal/body panel of your vehicle.
A minor scratch is one that doesn’t pass through the clear coat and colour – these are much easier to fix than deeper scratches that penetrate through to the primer or metal body of your car.
You Will Need:
- Buffer pads
- Spray bottle
- Rubbing compound
- Car wax
- Custom paint that matches your vehicle
For Shallow Scratches:
Step 1: Wash
Thoroughly wash and dry your vehicle, paying close attention to the scratched area.
Step 2: Sand
Lightly sand the scratched area in the direction of the scratch, taking care to sand through the clear coat only, but no further. Rinse the area with water every now and then, and avoid catching dirt on your sandpaper as this will only cause further scratching. Once you’re finished sanding, rinse the area then dry it with a microfiber cloth.
Step 3: Apply Rubbing Compound
Next, apply your rubbing compound using a buffer pad. This is an abrasive that smooths the paint surface and prepares it for waxing. You’ll want to move onto the next step fairly quickly so that the rubbing compound does not dry out.
Step 4: Polish the Area
Polish the area with a buffer pad – using the lowest level available – for about ten seconds. Then, turn up the speed to 2000 RPM for one minute, using a side to side then downward motion. Keep polishing until dullness is gone, but don’t polish the same spot for more than one second at a time as you may go through the paint layer.
Step 5: Wash and Wax
Lastly, wash the area once more, then wax to seal the newly applied paint.
For Deep Scratches
If you can see metal or a different colour through your scratch, you’re dealing with a that penetrates through to the primer or metal of your vehicle. Not to worry – these can still be removed with a little extra work:
Step 1: Get the Right Paint Colour
In order to find the exact colour of your car’s paint job, look for the factory-paint code on a metal plaque or a sticker in the doorsill, or under the hood of your car. Small scratches are just big enough to stop your fingernail in our test. These car scratch remover have dug down into the base coat. But don’t worry, you can still get them out using basic tools and materials using a car scratch repair kit. Remember to wash your car before attempting to remove the scratch.
Step 2: Clean the Area
Wash the scratched area thoroughly with solvent.
Step 3: Apply Colour
Now it’s time to do your touch up – carefully apply the correct colour paint or primer to the scratched area. If you’re using a pen, make sure to shake well before you begin application. A fine-tipped touch up brush works just as well – simply make sure to keep a steady hand while painting to avoid leaving unsightly brush strokes behind. Let your newly-applied paint cure overnight.
Step 4: Sand
The next day, use a 600- or 1000-grit sandpaper (with a rubber block or sponge as backing) to sand the area. Keep sanding until any paint standing out from the surface is smoothed down, cleaning the area often.
Step 5: Apply Compound
Rub compound into the damaged area to return its glossy finish.
Step 6: Paint & Compound Again
Repeat the painting process until the scratched is completely filled and level, then apply compound once more. Make sure not to wax your car for at least a month to allow all the solvents to escape.
Step 7: Apply Clear Coat
The last step of the deep scratch repair process is to apply a layer of clear coat.
First, clean the area with solvent, then spray a light coat or clear coat, and let it dry. Sand off excess product with sandpaper, then apply compound. Apply at least 2 coats of clear coat and compound, making sure to let the product dry for 24 hours between each coat.